In this article in the next paragraph you'll find lots of good quality insights involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
Mounting a bath tub isn't precisely brain surgery, however it does need solid plumbing, carpentry, and also occasionally, tiling abilities. Changing an old bath tub with a new one is likewise a moderately tough job. If the old bathtub is easily easily accessible, the project can move quickly; if you have to open a wall to get rid of the old tub and position the new bathtub, the task is much harder. In either case, the project is within a home handyman's skills, although you will need an assistant to leave the old bathtub and set in the brand-new one. Make sure you have certified yourself for the work and also are comfortable attempting it. Rather than working with a service provider to take control of a halfway-completed job, it is better to take into consideration employing one before you start. Possibilities are you may need a specialist plumber to make tube links.
This short article will certainly assist you install a brand-new bath tub in your restroom if you have currently gotten a new bathtub and also do not need to transform the plan of your previous water supply pipelines.
Your tools and also product list need to consist of the following:
Getting ready for the Setup
First of all, the supporting frame provided with the bathroom must be fitted (if needed) according to the producer's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is necessary to make certain that if the tap features a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets unit to stop stress on the bathtub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you utilize all of the provided washers.
Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its final placement.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the water system. After doing so, activate the faucets to drain any type of water continuing to be in the system. The process of eliminating the existing faucets can be fairly problematic because of the limited accessibility that is typically the instance.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a towel all set for the continuing to be water that will certainly come from the pipes. Once the supply pipelines have actually been eliminated, utilize the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from turning during this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned of any old securing substance.
Prior to carrying on to fit the brand-new taps, compare the pipeline links on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.
Mounting the Tub
Utilizing both wooden boards under its feet, position the tub in the needed position. The wood boards are valuable in evenly spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 little points.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by checking the level and readjusting the feet on the tub until the level reads degree.
To set up taps, fit the bottom of the furthest flexible faucet connector to the ideal supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the water and also inspect all joints and new pipework for leakages as well as tighten them if required. Fill the bath tub as well as likewise check the overflow electrical outlet as well as the typical outlet for leakages.
Lastly, repair the bathroom paneling as explained in the producer's user's manual. Tiling and also securing around the bathtub needs to wait till the bathtub has been utilized at least when as this will certainly settle it right into its final position.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the faucet as well as the other end supplies a connection to the current supply pipes.
If you need to fit a monobloc, after that you will call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making certain that the washers remain in place in between the tap and also the sink. Protect the faucet in place with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap ports. The former type needs to be linked to the faucet ends initially, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bath satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to split an inflexible seal, causing the water to permeate the wall surface in between the bathroom and the tiling, resulting in issues with wetness and also possible leaks to the ceiling below.
You can select from a range of coloured sealers to assimilate your components and fittings. They are sold in tubes as well as cartridges, as well as can securing voids approximately a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked paper or soft rope. Keep in mind to constantly load the bath tub with water prior to securing, to enable the motion experienced when the tub is in use. The sealant can crack rather very early if you do not think about this activity before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily readily available on the marketplace. It is a good idea to fit the ceramic tiles using water-resistant or water-proof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you enjoyed our article about A Step-by-Step Guide to Installing a Bathtub. Thank you for taking a few minutes to read through our blog post. Enjoyed our write-up? Please share it. Help others check it out. I recognize the value of reading our article about How to Install a Bathtub.
About